Osburn OB02401 Manual do Utilizador

READ AND KEEP THIS MANUAL FOR REFERENCE 45111A Printed in Canada 12-06-2015 OWNER`S MANUAL 2400 INSERT (OB02401 model) US ENVIRONMENTAL PRO

10 2.6 Positioning the unit In addition to ensuring compliance of the masonry fireplace hearth extension (see Compliance of the masonry fireplace in

11 If a non-combustible material floor protection needs to be added in front and level with the hearth extension masonry fireplace (see Figure 2.

12 The use of an R value is convenient when more than one material is going to be used in the hearth extension to cover the combustible surface.

13 The more extended the insert, the greater the heat transfer to the room. When installed as an extended insert, the front edge of the air jacket

14 Thermal characteristics of common floor protection materials* MATERIAL CONDUCTIVITY (k) PER INCH RESISTANCE (R) PER INCH THICKNESS Micore® 160 0.

15 MINIMUM MASONRY OPENING J 23 1/2" (597 mm) K 31 5/8" (803 mm) L 16 1/4" (412 mm) CLEARANCES F 14” (356 mm) G 8” (203 mm) H 2

16 2.8 Connector installation A masonry flue connector may provide acceptable performance (Figure 2.8a); however, we recommend the use

17 2.8.1 Chimney liner installation To install of the chimney liner, the preferred methods are those found in Section 2.8.1.1. Use a liner offset ada

18 2.8.1.2 If the chimney liner does not align with the insert’s flue outlet: You can get a liner offset adapter (AC01370), sold separately. If you m

19 C. Place the slide onto the faceplate so that the bends of the faceplate pieces go inside of the slide. 2400 INSERT FACEPLATE BOLT ASSEMBLY: Cont

2 INTRODUCTION SBI INC., one of the most important wood stove and fireplace manufacturers in Canada, congratulates you on your purchase

20 Back view of faceplate Figure 2.9d Lift the insert into the fireplace. Square the insert to the face of the fireplace by adjusting the leveli

21 2.10 Baffle & brick installation CAUTION: Operation of your Osburn insert without the baffle may cause unsafe and hazardous temperature con

22 Figure 2.10a 1- First, install the rear secondary air tube (B) in the firebox. Refer to figure 4.5: ‘’secondary air tube replacem

23 Figure 2.10b ITEM PIECE # DESCRIPTION QTY 1 29020 4 1/2" X 9" X 1 1/4'' REFRACTORY BRICK 12 2 PL36058 4" X 9"

24 3.0 OPERATION 3.1 Safety information 1. This insert is designed for safe operation WHEN BURNING CORDWOOD ONLY. Altering or modifying

25 10. Never operate the insert with the door open, or cracked slightly open, except briefly during the lighting operation, and during refuelling

26 Common Heating Values of Cordwood Hardwoods Million Btu/Cord Softwoods Million Btu/Cord Birch 23.6 Douglas Fir 20.6 White Oak 28.3 Hemlock

27 6. Ideally the large kindling should be burned until a thick bed of red embers is obtained. At that point, add cordwood fuel and continue to oper

28 Refuelling technique is important for good performance. The best efficiency and performance from your insert can be achieved by adding partial loa

29 4.0 MAINTENANCE 4.1 Care and cleaning Clean the insert frequently so that soot, ash and creosote do not accumulate. Do not attempt to clean th

3 TABLE OF CONTENTS 1.0 PRE-INSTALLATION REQUIREMENTS ... 4 1.1 MASON

30 4.3 Chimney cleaning Regular chimney maintenance, as well as good burning practices, are required to prevent chimney fires. The ch

31 4.5 Secondary air tube replacement (see Figure 4.5) 1. Remove cotter pin at LH end of tube. 2. Slide tube to right and lower tube end below LH

32 5.0 TROUBLESHOOTING Symptom Possible Cause Corrective Action I Smoke in room 1. Down draft 1. Upgrade chimney 2. Chimney blo

33 6.0 SPECIFICATIONS TEST STANDARDS ULC S628 (CSA B366.2) residential UL 1482 residential Oregon Department of Environmental Quality U.S. Env

34 OSBURN LIMITED LIFETIME WARRANTY The warranty of the manufacturer extends only to the original retail purchaser and is not transferable. This warr

4 1.0 PRE-INSTALLATION REQUIREMENTS 1.1 Masonry fireplace requirements The masonry fireplace must meet the minimum code requirements, or NFPA 211 or

5 1.2 Venting requirements The flue is a critical component to a satisfactory installation. Your insert will attain its best perfor

6 1.3 Door overlay installation In order to complete the assembly of your Osburn 2400 wood insert, you need to install the door overlay. See figure

7 2.0 INSTALLATION 2.1 Safety information NOTE: THIS APPLIANCE IS NOT RECOMMENDED FOR USE IN A HOME IF AN OCCUPANT HAS ANY RESPIRATORY OR ANY OTHE

8 2.2 Installation instructions Inspect the masonry fireplace according to the safety information and fireplace requirements and have it cleaned and/

9 2.4 The masonry fireplace's draft control system If the fireplace's draft control system is to remain in the masonry fireplace, it must b